دفتر مرکزی: 66097851     مرکز تعمیرات: 66097859   شعبه شرق :77978135   شعبه هفت تیر: 88836102   شعبه جنوب: 55300568 شعبه غرب 44153186 شعبه شمال 26721443  
شعبه اسلامشهر و رباط کریم 56746602

مرحله ۱ تعویض لولا  ها – درایو نوری

  • لپ تاپ را وارونه کنید.
  • پیچ ۶ میلیمتری را با پیچ گوشتی فیلیپس #۰۰۰ بردارید.

Flip the laptop over.Remove the 6 mm screw with the Phillips #000 screwdriver.

مرحله ۲

  • درایو نوری را به سمت بیرون بکشید تا برداشته شود.

Slide out the optical drive to remove it.

مرحله ۳- هارد دیسک

مچ بند ضد ایستا را قرار داده و گیره اتصال به شی فلزی را وصل کنید. این کار مانع از وارد شدن شوک به مادربرد می شود.

  • لپ تاپ را بچرخانید.
  • از پیچ گوشتی فیلیپس #۰۰۰ برای باز کردن پیچ ۶ میلیمتری از پنل مربعی استفاده نمایید.

Put on the anti-static wristband and connect the attached alligator clip to a metal object. This will prevent you from shocking the motherboard.Flip the laptop.

مرحله ۴

  • اسپادگر را به آرامی زیر پنل مربعی قرار دهید.
  • اسپادگر را زیر لبه های پنل مربعی حرکت داد تا شل شود.
  • پنل را بردارید.

Gently wedge the spudger under the square panel.Run the spudger under the edges of the square panel to loosen it.

مرحله ۵

هارد دیسک را به آرامی بردارید زیرا هنوز به یک سیم متصل است.

  • نوار لاستیکی را بکشید و یا اینکه از اسپادگر برای بلند کردن هارد دیسک استفاده کنید.

Remove the hard drive slowly because it is still connected to a wire.

مرحله ۶

  • کانکتور برق واقع در پایه سیم را به آرامی بکشید تا هارد دیسک جدا شود. این کار را می توان با کشیدن کانکتور از هارد دیسک نیز انجام داد.

Remove the hard drive by gently pulling the power connector at the base of the wire off. You can do this by pulling the connector away from the hard drive.

مرحله ۷- لولاها

  • سیم را بکشید تا از مادربرد قطع شود.
  • پیچ ۶ میلیمتری را با پیچ گوشتی فیلیپس #۰۰۰ بردارید.

Disconnect the wire from the motherboard by pulling up and away from the laptop.Remove the 6 mm screw with the Phillips #000 screwdriver.

مرحله ۸

  • دو توپی لاستیکی را با استفاده از موچین بردارید.

Remove the top two rubber stoppers using precision tweezers.Remove the top two rubber stoppers using precision tweezers.

مرحله ۹

  • ۹ پیچ ۶ میلیمتری واقع در کاور را با پیچ گوشتی فیلیپس #۰۰۰ بردارید.

Unscrew nine 6 mm screws on the cover using a Phillips #000 screwdriver.

مرحله ۱۰

  • اسپادگر را زیر کاور قرار داده و آن را به آرامی بلند کنید.

Wedge the spudger under the cover to gently pry it up.Wedge the spudger under the cover to gently pry it up.Wedge the spudger under the cover to gently pry it up.

مرحله ۱۱

  • از ابزار بازکننده پلاستیکی برای بلند کرد کانکتور از مادربرد استفاده نموده و سیم را به دقت قطع کنید.

Disconnect the wire by carefully using the plastic opening tool to pry the connector away from the motherboard.Disconnect the wire by carefully using the plastic opening tool to pry the connector away from the motherboard.Disconnect the wire by carefully using the plastic opening tool to pry the connector away from the motherboard.

مرحله ۱۲

  • سیم های آنتن را با موچین از کارت وای فای بلند کنید.

Use precision tweezers to pop the antenna wires off of the WiFi card.Use precision tweezers to pop the antenna wires off of the WiFi card.Use precision tweezers to pop the antenna wires off of the WiFi card.

مرحله ۱۳

  • لپ تا را اندکی باز کنید.
  • لپ تاپ را نگهدارید، ۳ پیچ ۴ میلیمتری را از هر لولا ((در کل ۶ تا) با استفاده از پیچ گوشتی فیلیپس #۰۰۰ بردارید.

Open the laptop slightly.Holding the laptop open, remove three 4 mm screws from each hinge (6 total) using a Phillips #000 screwdriver.Holding the laptop open, remove three 4 mm screws from each hinge (6 total) using a Phillips #000 screwdriver.

مرحله ۱۴

  • لولاها را با شست گرفته و لپ تاپ را از قسمت صفحه حرکت دهید.

Hold hinges in place with your thumb and slide the laptop away from the screen.

مرحله ۱۵

  • چهارمین توپی لاستیکی را با موچین بردارید.

Remove the 4 rubber stoppers with the precision tweezers.Remove the 4 rubber stoppers with the precision tweezers.

مرحله ۱۶

  • ۴ پیچ ۴ میلیمتری را با پیچ گوشتی فیلیپس #۰۰۰ بردارید.

Remove the four 4 mm screws with a Phillips #000 screwdriver.Remove the four 4 mm screws with a Phillips #000 screwdriver.

مرحله ۱۷

اسپادگر فلزی می تواند صفحه را مخدوش کند.

  • اسپادگر فلزی را زیر کاور قرار داده و آن را در امتداد لبه ها حرکت دهید. کاور را به آرامی بلند نمایید.

The metal spudger could scratch the screen.Wedge the metal spudger underneath the cover and run it along the edges. Gently pry the cover up.

مرحله ۱۸

پیچ های ۴ میلیمتری واقع در هر لولا را با پیچ گوشتی فیلیپس #۰۰۰ بردارید. احتمالا ۶ پیچ وجود دارند.

Remove the three 4 mm screws on each hinge with a Phillips #000 screwdriver. There should be a total of 6 screws to remove.Remove the three 4 mm screws on each hinge with a Phillips #000 screwdriver. There should be a total of 6 screws to remove.

 

مرتبط: تعویض کیبورد NP-N145-JP02US سامسونگ

اطلاعات بیشتر درمورد این لپ تاپ

دیدگاه‌ خود را بنویسید

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

بیست − 5 =